Height 30 mm/1.181"
Length: 121 mm/4.76"
Prevents damage on scope due to flexing during heavy recoil or rough environment. The snipers rifle and the spotters carbine can have the same mount, enabling the use of same equipment and accessories. Rings are grooved inside to get a better grip of the scope and enabling gluing of the scope. The mount is milled out of one billet of material instead of being screwed together from small parts.
Patent pending solution for indexing the rotation of the scope, using an included tool/gauge to index the scope correctly to the mount and gun. Important since an incorrectly indexed scope unintentionally will also have a sideways adjusted point of impact and since it will be adjusted sideways when it is adjusted for elevation.
Traditionally lasers have been mounted on the forend of the rifle, a solution with drawbacks. For the same reasons you don′t want your barrel to touch the forend, you don′t want the sights to be mounted on the forend. Our mounting system has a minimum of seven interfaces for accessories and the laser can easily be mounted on the mount, giving the advantage of an undisturbed laser and a weight more central on the gun instead of forward.
Accessible and Readable Dials
The rings are cut 45 degrees instead of the usual horizontal, providing several advantages. The screws holding the parts together are not in the way of the knobs, thus the shooter can quickly determine the settings of the knobs. It also gives the shooter a horizontal line that helps the shooter not torotate his gun unintentionally. The rings have index marks on the top and right side, making low knobs more easily readable.
Possibility of using various accessories such as angle cosine indicator, back up sights, lasers, illuminators, Night vision mounts etc. With traditional mounts this can be achieved only if there is sufficient space on the middle tube for additional rings, which there rarely is. Ideal Scope Mount Systems have interface surfaces directly on the mount, making it possible to mount accessories either by Picatinny rails or as direct interfaces for certain accessories such as angle cosine indicators and red dot sights. A selection of interfaces for popular accessories are available, and others can be made to specification.
My third mount from spuhr, alignment tool makes mounting fast & easy !
Don't use anything else. These mounts don't move at all once they are installed, properly. I have several QD and several normal spuhr mounts. Have never had to re mount anything, even after several years, many trips, drops and bangs. Worth the money. Only down side is, not a lot of forward or backward movement for the scope. Check your eye relief to make sure you have enough for the chassis/ stock you put it on.
I own several Spuhr mounts. This particular mount is for a Vortex Razor Gen II. The gun itself is a custom build in 6.5 Creedmoor. I just finished a long range class, and sent 1000 rounds down range. I just rechecked the torque on all the screws--nothing moved!!
I mounted this on a 6.5 Creedmoor rifle. The mount is built like a tank. Very well engineered. I own many other mounts, including the well known Badger Ordinance, and this mount is simply far superior. I liked this one so much I purchased another one for a .308 rifle. While pricey, well worth the expense especially if you've mounted a high end scope to the rifle.
I recently used this product to mount my new Nightforce scope to a Highly customized Savage 11 in 6.5 Creedmoor. Mounting the scope to the rifle was probably the easiest one I have ever done. As the other gentleman said, the installation tool makes it very easy to mount properly and completely removes the need for levels. I will be using these mounts going forward on every project where it is suitable.
I used this (4001) to mount a K624i (56mm) to a heavy varmint barreled rifle (Kreiger #17). Plenty of clearance while still being close. Height over bore ended up 2.658".
There is not a lot of forward backward movement available in this mount, it hugged the turrets pretty tight. I mounted my scope all the way forward in the rings so I could see the turrets without taking my eye off the scope. I can see the bubble in the bottom of the mount, my left hand windage turret, and elevation turret. The top parallax is not visible without losing contact with the target and reticle.
Torqued to 20 in/lb on the rings and 45 in/lb on the cross bolts. The leveling wedge was very helpful. No levels required. Rock Solid. I don't expect to go back to rings on future builds.